diff --git a/xymon/get.xymon.alert.vars.sh b/xymon/get.xymon.alert.vars.sh
new file mode 100755
index 0000000..3b20918
--- /dev/null
+++ b/xymon/get.xymon.alert.vars.sh
@@ -0,0 +1,23 @@
+#!/bin/sh
+
+log_file="/tmp/xymon.alert.${BBHOSTSVC}.vars"
+
+# Print variables for an alert on a specific host
+rm -f -- "${log_file}"
+touch "${log_file}"
+printf '%b' "BBCOLORLEVEL=\"${BBCOLORLEVEL}\"\\n" >> "${log_file}"
+printf '%b' "BBALPHAMSG=\"${BBALPHAMSG}\"\\n" >> "${log_file}"
+printf '%b' "ACKCODE=\"${ACKCODE}\"\\n" >> "${log_file}"
+printf '%b' "RCPT=\"${RCPT}\"\\n" >> "${log_file}"
+printf '%b' "BBHOSTNAME=\"${BBHOSTNAME}\"\\n" >> "${log_file}"
+printf '%b' "MACHIP=\"${MACHIP}\"\\n" >> "${log_file}"
+printf '%b' "BBSVCNAME=\"${BBSVCNAME}\"\\n" >> "${log_file}"
+printf '%b' "BBSVCNUM=\"${BBSVCNUM}\"\\n" >> "${log_file}"
+printf '%b' "BBHOSTSVC=\"${BBHOSTSVC}\"\\n" >> "${log_file}"
+printf '%b' "BBHOSTSVCCOMMAS=\"${BBHOSTSVCCOMMAS}\"\\n" >> "${log_file}"
+printf '%b' "BBNUMERIC=\"${BBNUMERIC}\"\\n" >> "${log_file}"
+printf '%b' "RECOVERED=\"${RECOVERED}\"\\n" >> "${log_file}"
+printf '%b' "DOWNSECS=\"${DOWNSECS}\"\\n" >> "${log_file}"
+printf '%b' "DOWNSECSMSG=\"${DOWNSECSMSG}\"\\n" >> "${log_file}"
+
+exit 0
diff --git a/xymon/plugins/client/ext/dcheck b/xymon/plugins/client/ext/dcheck
new file mode 100644
index 0000000..78593b5
--- /dev/null
+++ b/xymon/plugins/client/ext/dcheck
@@ -0,0 +1,8 @@
+3&green /dev/sda auto
+3&green /dev/sdb auto
+3&green /dev/sdc auto
+3&green /dev/sdd auto
+3&green /dev/sde auto
+4&clear /dev/sdf unsupported
+3&green /dev/bus/0 megaraid,12
+3&green /dev/bus/0 megaraid,13
diff --git a/xymon/plugins/client/ext/dres b/xymon/plugins/client/ext/dres
new file mode 100644
index 0000000..b4b490f
--- /dev/null
+++ b/xymon/plugins/client/ext/dres
@@ -0,0 +1,258 @@
+&green /dev/sda auto
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               HGST
+Product:              HUS728T8TAL5200
+Revision:             RS01
+Compliance:           SPC-4
+User Capacity:        8,001,563,222,016 bytes [8.00 TB]
+Logical block size:   512 bytes
+Physical block size:  4096 bytes
+Formatted with type 2 protection
+LU is fully provisioned
+Rotation Rate:        7200 rpm
+Form Factor:          3.5 inches
+Logical Unit id:      0x5000cca09976b8c4
+Serial number:        VAJ392BL
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:11 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  96    5771                 - [-   -    -]
+# 2  Background short  Completed                  96    5747                 - [-   -    -]
+------------------------------------------------------------
+
+
+&green /dev/sdb auto
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               HGST
+Product:              HUS728T8TAL5200
+Revision:             RS01
+Compliance:           SPC-4
+User Capacity:        8,001,563,222,016 bytes [8.00 TB]
+Logical block size:   512 bytes
+Physical block size:  4096 bytes
+Formatted with type 2 protection
+LU is fully provisioned
+Rotation Rate:        7200 rpm
+Form Factor:          3.5 inches
+Logical Unit id:      0x5000cca09975fc04
+Serial number:        VAJ2WHPL
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:11 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  96    5607                 - [-   -    -]
+# 2  Background short  Completed                  96    5583                 - [-   -    -]
+------------------------------------------------------------
+
+
+&green /dev/sdc auto
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               HGST
+Product:              HUS728T8TAL5200
+Revision:             RS01
+Compliance:           SPC-4
+User Capacity:        8,001,563,222,016 bytes [8.00 TB]
+Logical block size:   512 bytes
+Physical block size:  4096 bytes
+Formatted with type 2 protection
+LU is fully provisioned
+Rotation Rate:        7200 rpm
+Form Factor:          3.5 inches
+Logical Unit id:      0x5000cca099757c5c
+Serial number:        VAJ2M04L
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:11 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  96    5859                 - [-   -    -]
+# 2  Background short  Completed                  96    5835                 - [-   -    -]
+------------------------------------------------------------
+
+
+&green /dev/sdd auto
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               HGST
+Product:              HUS728T8TAL5200
+Revision:             RS01
+Compliance:           SPC-4
+User Capacity:        8,001,563,222,016 bytes [8.00 TB]
+Logical block size:   512 bytes
+Physical block size:  4096 bytes
+Formatted with type 2 protection
+LU is fully provisioned
+Rotation Rate:        7200 rpm
+Form Factor:          3.5 inches
+Logical Unit id:      0x5000cca099765214
+Serial number:        VAJ327BL
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:11 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  96    5599                 - [-   -    -]
+# 2  Background short  Completed                  96    5575                 - [-   -    -]
+------------------------------------------------------------
+
+
+&green /dev/sde auto
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               HGST
+Product:              HUS728T8TAL5200
+Revision:             RS01
+Compliance:           SPC-4
+User Capacity:        8,001,563,222,016 bytes [8.00 TB]
+Logical block size:   512 bytes
+Physical block size:  4096 bytes
+Formatted with type 2 protection
+LU is fully provisioned
+Rotation Rate:        7200 rpm
+Form Factor:          3.5 inches
+Logical Unit id:      0x5000cca09976e460
+Serial number:        VAJ3BZDL
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:11 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  96    5599                 - [-   -    -]
+# 2  Background short  Completed                  96    5575                 - [-   -    -]
+------------------------------------------------------------
+
+
+&clear /dev/sdf unsupported
+
+SMART Health Status can't be determine because of:
+SMART support is:     Unavailable - device lacks SMART capability.
+
+=== START OF INFORMATION SECTION ===
+Vendor:               DELL
+Product:              PERC H730P Mini
+Revision:             4.30
+User Capacity:        146,163,105,792 bytes [146 GB]
+Logical block size:   512 bytes
+Logical Unit id:      0x61866da06192eb00256e8c0a2d73f5b6
+Serial number:        00b6f5732d0a8c6e2500eb9261a06d86
+Device type:          disk
+Local Time is:        Fri Feb 28 15:07:12 2020 CET
+SMART support is:     Unavailable - device lacks SMART capability.
+
+
+------------------------------------------------------------
+
+
+&green /dev/bus/0 megaraid,12
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               SEAGATE
+Product:              ST9146803SS
+Revision:             FS64
+User Capacity:        146,815,733,760 bytes [146 GB]
+Logical block size:   512 bytes
+Rotation Rate:        10000 rpm
+Form Factor:          2.5 inches
+Logical Unit id:      0x5000c5003ac7ef07
+Serial number:        6SD3HJV0
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:13 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  16   62479                 - [-   -    -]
+# 2  Background short  Completed                  16   62455                 - [-   -    -]
+------------------------------------------------------------
+
+
+&green /dev/bus/0 megaraid,13
+
+SMART Health Status: OK
+&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase
+=== START OF INFORMATION SECTION ===
+Vendor:               SEAGATE
+Product:              ST9146803SS
+Revision:             FS64
+User Capacity:        146,815,733,760 bytes [146 GB]
+Logical block size:   512 bytes
+Rotation Rate:        10000 rpm
+Form Factor:          2.5 inches
+Logical Unit id:      0x5000c5003ac956db
+Serial number:        6SD3HH6J
+Device type:          disk
+Transport protocol:   SAS (SPL-3)
+Local Time is:        Fri Feb 28 15:07:14 2020 CET
+SMART support is:     Available - device has SMART capability.
+SMART support is:     Enabled
+Temperature Warning:  Disabled or Not Supported
+
+=== START OF READ SMART DATA SECTION ===
+SMART Self-test log
+Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
+     Description                              number   (hours)
+# 1  Background short  Completed                  16   61374                 - [-   -    -]
+# 2  Background short  Completed                  16   61350                 - [-   -    -]
+------------------------------------------------------------
+
+
diff --git a/xymon/plugins/client/ext/dscan b/xymon/plugins/client/ext/dscan
new file mode 100644
index 0000000..d7a76f8
--- /dev/null
+++ b/xymon/plugins/client/ext/dscan
@@ -0,0 +1,13 @@
+/dev/sda -d scsi # /dev/sda, SCSI device
+/dev/sdb -d scsi # /dev/sdb, SCSI device
+/dev/sdc -d scsi # /dev/sdc, SCSI device
+/dev/sdd -d scsi # /dev/sdd, SCSI device
+/dev/sde -d scsi # /dev/sde, SCSI device
+/dev/sdf -d scsi # /dev/sdf, SCSI device
+/dev/bus/0 -d megaraid,0 # /dev/bus/0 [megaraid_disk_00], SCSI device
+/dev/bus/0 -d megaraid,1 # /dev/bus/0 [megaraid_disk_01], SCSI device
+/dev/bus/0 -d megaraid,2 # /dev/bus/0 [megaraid_disk_02], SCSI device
+/dev/bus/0 -d megaraid,3 # /dev/bus/0 [megaraid_disk_03], SCSI device
+/dev/bus/0 -d megaraid,4 # /dev/bus/0 [megaraid_disk_04], SCSI device
+/dev/bus/0 -d megaraid,12 # /dev/bus/0 [megaraid_disk_12], SCSI device
+/dev/bus/0 -d megaraid,13 # /dev/bus/0 [megaraid_disk_13], SCSI device
diff --git a/xymon/plugins/client/ext/sge.sh b/xymon/plugins/client/ext/sge.sh
new file mode 100755
index 0000000..6c83b23
--- /dev/null
+++ b/xymon/plugins/client/ext/sge.sh
@@ -0,0 +1,242 @@
+#!/bin/sh
+#
+# SGE: Sun Grid Engine check - Xymon external script test
+#
+#####  Purpose is to report back to a central server, all Sun
+#####     Grid Engine software faults.
+#####
+#
+# version 0.4
+#
+# BIG BROTHER / XXXXXXXXXXXXXXXX status
+#
+# Written by Butch Deal <butchdeal@yahoo.com>
+#	     Daniel Gomez <dgomez@tigr.org,daniel@ixplosive.com>
+#	     Jérémy Gardais <jeremy.gardais@univ-rennes1.fr>
+#
+# v0.4 09/06/20  clean, correction,… for Xymon 4.3.28
+# v0.3e 10/14/08 cut down on the number of qhost runs
+# v0.3d 03/31/06 added alarm/suspend state identification
+# v0.3c 03/01/06 propogated yellow state upon UNAVAILABLE queue intances
+# v0.3b 01/31/06 fixed yellow warning queue status for ambigious config test
+# v0.3a 01/31/06 added unknown queue status and ambigious config test
+# v0.3 01/26/06 fixed status reporting and optimized job status
+# v0.2 08/03/05 flag disabled queues as clear
+# v0.1 07/28/05 authored
+
+########################################
+# NOTE
+# The version v0.4 has only been tested with Xymon (server and client) 4.2.x.
+#
+# The color status with respects to queue status is arbitrary and should be
+# reviewed for your particular environment.
+#
+# Tested on :
+#   Solaris & Linux
+#   Linux only (for v0.4)
+########################################
+
+########################################
+# INSTALLATION
+#  step 1  - copy to Xymon client's ext dir
+#  step 2  - New clientlaunch.d/sge.cfg file
+#  step 3  - restart Xymon client
+#
+# NOTE - the TEST variable in the configuration section, this is the name used
+#        as the column header.
+########################################
+
+##################################
+# CONFIGURE IT HERE
+##################################
+readonly PLUGIN_NAME=$(basename "${0}")
+
+readonly TEST="sge"
+readonly PLUGIN_RESULT="${XYMONTMP}/${MACHINEDOTS}.${TEST}.plugin_result"
+readonly PLUGIN_STATE="${XYMONTMP}/${MACHINEDOTS}.${TEST}.plugin_state"
+true > "${PLUGIN_STATE}"
+
+readonly QSTAT=$(command -v qstat)
+readonly QHOST=$(command -v qhost)
+readonly QSELECT=$(command -v qselect)
+export QSTAT QHOST QSELECT
+
+# define colours for graphics
+# Comment these out if using older BB versions
+CLEAR_PIC="&clear"
+RED_PIC="&red"
+YELLOW_PIC="&yellow"
+GREEN_PIC="&green"
+UNKNOWN_PIC="&purple"
+
+##################################
+# Start of script
+##################################
+
+get_header()
+{
+	echo ""
+	#echo "<FONT SIZE=+2><b>$1</b></FONT> ($2)<BR>"
+	echo "<FONT SIZE=+2><b>$1</b></FONT> <BR>"
+	# If you do not want the header in a bigger font use line below instead
+	#echo "<b>$1</b> ($2)"
+	# If you want the "Paul Luzzi" look uncomment this section and comment
+	# out the above sections:
+	#echo "<P><DIV ALIGN=\"CENTER\"><HR>"
+	#echo "<B>============== $1 ==============</B>"
+	#echo "<B>--- ($2) ---</B>"
+	#echo "<HR></DIV>"
+	#echo "<BLOCKQUOTE>"
+}
+get_header_small()
+{
+	echo ""
+	#echo "<FONT SIZE=+2><b>$1</b></FONT> ($2)<BR>"
+	echo "<FONT SIZE=+1><b>$1</b></FONT> <BR>"
+	# If you do not want the header in a bigger font use line below instead
+	# echo "<b>$1</b> ($2)"
+	# If you want the "Paul Luzzi" look uncomment this section and comment
+	# out the above sections:
+	#echo "<P><DIV ALIGN=\"CENTER\"><HR>"
+	#echo "<B>============== $1 ==============</B>"
+	#echo "<B>--- ($2) ---</B>"
+	#echo "<HR></DIV>"
+	#echo "<BLOCKQUOTE>"
+}
+
+
+get_footer()
+{
+	echo ""
+	# If you want the "Paul Luzzi" look uncomment this section and comment
+	# out the above sections:
+	#echo "</BLOCKQUOTE>"
+}
+
+#####
+#####  Get Status proc - used to get all responses
+#####
+get_status()
+{
+
+	# Check defaults have been set
+	if [ "${QSTAT}" = "" ]; then
+		readonly QSTAT=$(command -v qstat)
+		echo ""
+		echo "$YELLOW_PIC QSTAT command is not defined in etc/bbsys.local - using default: ${QSTAT}"
+	fi
+
+	if [ "${QHOST}" = "" ]; then
+		readonly QHOST=$(command -v qhost)
+		echo ""
+		echo "$YELLOW_PIC QHOST command is not defined in etc/bbsys.local - using default: ${QHOST}"
+	fi
+
+	if [ "${QSELECT}" = "" ]; then
+		readonly QSELECT=$(command -v qselect)
+		echo ""
+		echo "$YELLOW_PIC QSELECT command is not defined in etc/bbsys.local - using default: ${QSELECT}"
+	fi
+
+	###
+	### Check the jobs
+	###
+	get_header "Jobs" "$QSTAT -l hostname=$MACHINEDOTS"
+	jobs=$(${QSTAT} -l hostname="${MACHINEDOTS}" -s r -u \*)
+	if [ -z "$jobs" ]; then
+		echo "No Running Jobs"
+	else
+		${QSTAT} -l hostname="${MACHINEDOTS}" -s r -u \*
+	fi
+	get_footer
+
+	###
+	### Check the host
+	###
+	get_header "Host" "$METAHS -i"
+	${QHOST} -h "${MACHINEDOTS}" | grep -v "global"
+	get_footer
+
+	###
+	### Identify queue memberships
+	###
+	#get_header "Queue Membership" "$QHOST -q"
+	#${QHOST} -h ${MACHINEDOTS} -q | tail +5
+	#get_footer
+
+	###
+	### Check queue instance states
+	###
+	queueTriggered=false;
+	${QHOST} -h "${MACHINEDOTS}" -q | tail +5 > "${PLUGIN_RESULT}.QSTATE"
+	while IFS= read -r _LINE; do
+		queue=$(printf -- '%s' "${_LINE}" | awk '{ print $1 }')
+		qstate=$(printf -- '%s' "${_LINE}" | awk '{ print $4 }')
+
+		# Order determines more significant alert status
+		if [ "$(echo "${qstate}" | grep -c d)" != "0" ]; then
+			echo "4&clear $queue@$HOST is DISABLED" >> "${PLUGIN_STATE}"
+			queueMsg=$(echo "$queueMsg<BR>$CLEAR_PIC $queue@$HOST is DISABLED<BR>${_LINE}")
+			queueTriggered=true;
+		elif [ "$(echo "${qstate}" | grep -c E)" != "0" ]; then
+			echo "1&red $queue@$HOST is in ERROR!" >> "${PLUGIN_STATE}"
+			queueMsg=$(echo "$queueMsg<BR>$RED_PIC $queue@$HOST is in ERROR!<BR>${_LINE}")
+			queueTriggered=true;
+		elif [ "$(echo "${qstate}" | grep -c c)" != "0" ]; then
+			echo "2&yellow $queue@$HOST has an ambigious configuration!" >> "${PLUGIN_STATE}"
+			queueMsg=$(echo "$queueMsg<BR>$YELLOW_PIC $queue@$HOST has an ambigious configuration!<BR>${_LINE}")
+			queueTriggered=true;
+		elif [ "$(echo "${qstate}" | grep -c a)" != "0" ] || \
+			[ "$(echo "${qstate}" | grep -c A)" != "0" ]; then
+				echo "2&yellow $queue@$HOST is in ALARM" >> "${PLUGIN_STATE}"
+				queueMsg=$(echo "$queueMsg<BR>$YELLOW_PIC $queue@$HOST is in ALARM<BR>${_LINE}")
+			elif [ "$(echo "${qstate}" | grep -c s)" != "0" ] || \
+				[ "$(echo "${qstate}" | grep -c S)" != "0" ]; then
+					echo "2&yellow $queue@$HOST is SUSPENDED" >> "${PLUGIN_STATE}"
+					queueMsg=$(echo "$queueMsg<BR>$YELLOW_PIC $queue@$HOST is SUSPENDED<BR>${_LINE}")
+				elif [ "$(echo "${qstate}" | grep -c u)" != "0" ]; then
+					echo "2&yellow $queue@$HOST is UNAVAILABLE" >> "${PLUGIN_STATE}"
+					queueMsg=$(echo "$queueMsg<BR>$YELLOW_PIC $queue@$HOST is UNAVAILABLE!<BR>${_LINE}")
+					queueTriggered=true;
+				elif [ "$qstate" = "" ]; then
+					echo "3&green $queue@$HOST is OK" >> "${PLUGIN_STATE}"
+					queueMsg=$(echo "$queueMsg<BR>$GREEN_PIC $queue@$HOST is OK<BR>${_LINE}")
+				else
+					echo "5&purple $queue@$HOST is UNKNOWN" >> "${PLUGIN_STATE}"
+					queueMsg=$(echo "$queueMsg<BR>$UNKNOWN_PIC $queue@$HOST is UNKNOWN<BR>${_LINE}")
+					queueTriggered=true;
+		fi
+	done < "${PLUGIN_RESULT}.QSTATE"
+
+	get_header "Queue Instance Status Report"
+	echo "$queueMsg"
+	get_footer
+
+#####
+#####  End of get_status proc
+#####
+}
+
+#####
+#####  Main body
+#####
+get_status > "${PLUGIN_RESULT}"
+
+# Set the global color according to the highest alert
+COLOR=$(< "${PLUGIN_STATE}" awk '{print $1}' | sort | uniq | head -1 | cut -c3-)
+
+	# NOW USE THE XYMON COMMAND TO SEND THE DATA ACROSS
+	$XYMON "${XYMSRV}" "status ${MACHINE}.${TEST} ${COLOR} $($DATE) $(cat ${PLUGIN_RESULT})"
+	#For testing only
+	#       echo $XYMON "${XYMSRV}" "status ${MACHINE}.${TEST} ${COLOR} $($DATE) $(cat ${PLUGIN_RESULT})" > /tmp/sgetmp
+
+# Clean up our mess
+# Checking for existence of each file since the whole test may be optional
+#   and may not actually run on every client
+#
+if [ -f "${PLUGIN_RESULT}" ]; then
+	rm -f -- "${PLUGIN_RESULT}" "${PLUGIN_STATE}" "${PLUGIN_RESULT}.QSTATE"
+fi
+##############################################
+# end of script
+##############################################
diff --git a/xymon/plugins/client/ext/smart b/xymon/plugins/client/ext/smart
new file mode 100755
index 0000000..1de176b
--- /dev/null
+++ b/xymon/plugins/client/ext/smart
@@ -0,0 +1,202 @@
+#!/usr/bin/perl
+# $Id: sensors 70 2011-11-25 09:21:18Z skazi $
+# Author: Jacek Tomasiak <jacek.tomasiak@gmail.com>
+# https://github.com/skazi0/xymon-plugins/blob/master/client/ext/smart
+
+use strict;
+# add script's directory to module search path for Hobbit.pm on non-debian systems
+use FindBin;
+use lib $FindBin::Bin;
+
+use Hobbit;
+use Data::Dumper;
+
+my $bb = new Hobbit('smart');
+
+my $temp_disk_list = "$ENV{'XYMONTMP'}/$ENV{'MACHINEDOTS'}.smart.drivedb.list";
+my @disks = ();
+my %olderr = {};
+
+my $CACHETIME = 10; # minutes
+my $CACHEFILE = "$ENV{'XYMONTMP'}/$ENV{'MACHINEDOTS'}.smart.cache";
+
+&load_config("$ENV{'XYMONTMP'}/logfetch.$ENV{'MACHINEDOTS'}.cfg");
+
+my @disks_stat = stat($temp_disk_list);
+my $disks_mtime = scalar @disks_stat ? $disks_stat[9] : 0;
+#
+# Regenerate disks list if the file is too old (600 minutes)
+if (time() - $disks_mtime > 600)
+{
+    unlink $temp_disk_list;
+}
+
+if (-e $temp_disk_list) {
+    # Should use the existing file
+}
+else {
+    # Create a file with the list of disks
+    system("ls -1 /dev/sd* | grep -vE '[0-9]' > $temp_disk_list") == 0
+        or die "system command to create $temp_disk_list failed: $?";
+}
+
+# fallback to disk detection if nothing defined in the config
+unless (@disks) {
+    ## Put temp_disk_list content to disks array
+    open(my $fh, '<:encoding(UTF-8)', $temp_disk_list)
+        or die "Could not open file '$temp_disk_list' $!";
+    while (my $row = <$fh>) {
+        chomp $row;
+        push(@disks, "$row");
+    }
+}
+
+my @stat = stat($CACHEFILE);
+my $mtime = scalar @stat ? $stat[9] : 0;
+# regenerate sensors cache if outdated
+if (time() - $mtime > $CACHETIME * 60)
+{
+    open(OUT, ">$CACHEFILE") or die "cannot open $CACHEFILE";
+
+    foreach my $name (@disks)
+    {
+        print OUT ('=' x 20) . " $name " . ('=' x 20) . "\n";
+        my @output = `sudo smartctl -AHi -l error -l selftest $name 2>&1` or die;
+        my $ncv = '';
+        my $newerr = 1;
+        my $ponhours = undef;
+        my $lasttest = undef;
+        foreach my $line (@output)
+        {
+            # skip header
+            next if ($line =~ /smartctl|Copyright|Home page|===/);
+
+            if ($line =~ /.*overall-health.*:\s*(.*)/)
+            {
+                my $lstatus = ($1 eq 'PASSED') ? 'green' : 'red';
+                print OUT "&$lstatus $line";
+            }
+            elsif ($line =~ /^\s*(\d+)\s+(\S+)\s+\S+\s+(\d+)\s+(\d+)\s+(\d+)\s+\S+\s+\S+\s+(\S+)\s+(.*)$/)
+            {
+                my ($aname, $value, $worst, $thresh, $failure, $raw) = ($2, $3, $4, $5, $6, $7);
+                my $lstatus = 'green';
+                if ($aname =~ /Current_Pending_Sector|Offline_Uncorrectable/ and int($raw) > 0)
+                {
+                    $lstatus = 'yellow';
+                }
+                elsif ($aname =~ /Power_On_Hours/)
+                {
+                    $ponhours = $raw;
+                }
+                if ($failure =~ /FAIL/) {
+                    $lstatus = 'red';
+                }
+
+                print OUT "&$lstatus $line";
+
+                $ncv .= "$name-$aname-value : $value\n";
+                $ncv .= "$name-$aname-worst : $worst\n";
+                $ncv .= "$name-$aname-thresh : $thresh\n";
+                $ncv .= "$name-$aname-raw : $raw\n";
+            }
+            elsif ($line =~ /^\s*No Errors Logged\s*$/)
+            {
+                $newerr = 0;
+                print OUT "&green $line";
+            }
+            elsif ($line =~ /Error Count:\s*(\d+)/)
+            {
+                $newerr = $1 - $olderr{$name};
+                my $lstatus = $newerr > 0 ? 'red' : 'green';
+                print OUT "&$lstatus $line"
+            }
+            elsif ($line =~ /^\s*Error \d+ occurred/)
+            {
+                my $lstatus = $newerr > 0 ? 'red' : 'green';
+                print OUT "&$lstatus $line"
+            }
+            elsif ($line =~ /^\s*#\s*\d+\s+(Conveyance offline|Extended offline|Short offline|Extended captive)\s+(.*)\s+\d+%\s+(\d+)/)
+            {
+                my $status = $2;
+                my $lifetime = $3;
+                my $lstatus = 'red';
+                $lasttest = $lifetime if (!defined($lasttest));
+                $lstatus = 'yellow' if ($status =~ /Aborted by host|Interrupted \(host reset\)/);
+                $lstatus = 'green' if ($status =~ /Completed without error|Self-test routine in progress|Interrupted \(host reset\)/);
+                print OUT "&$lstatus $line";
+            }
+            else
+            {
+                print OUT "   $line";
+            }
+        }
+        # test status footer
+        my $lasttestage = $ponhours % 65536 - $lasttest;
+        my $lasttestmsg = "$lasttestage hours ago";
+        my $lasttestcolor = 'green';
+        if (!defined($lasttest))
+        {
+                $lasttestcolor = 'yellow';
+                $lasttestmsg = 'no test performed';
+        }
+        elsif ($lasttestage > 24 * 7)
+        {
+                $lasttestcolor = 'red';
+        }
+        elsif ($lasttestage > 24 * 2)
+        {
+                $lasttestcolor = 'yellow';
+        }
+        print OUT "&$lasttestcolor Last Self-test: $lasttestmsg\n";
+
+        # hidden output for ncv
+        print OUT "<!--\n$ncv\n-->\n";
+    }
+
+    close OUT;
+}
+
+# send cached content
+{
+    open IN, $CACHEFILE or die "cannot open $CACHEFILE";
+    while (my $line = <IN>)
+    {
+        if ($line =~ /^\s*&(\S+)/)
+        {
+            $bb->color_print($1, $line);
+        }
+        else
+        {
+            $bb->print($line);
+        }
+    }
+    close IN;
+}
+
+
+$bb->send;
+
+sub load_config
+{
+    my $path = shift;
+
+    open C, "<$path" or return;
+#    print "loading config from $path\n";
+    while (my $line = <C>)
+    {
+        next if ($line =~ /^\s*#/);
+        if ($line =~ /DISKS\s*=\s*['"](.*?)["']/)
+        {
+            @disks = split(/\s+/, $1);
+        }
+        if ($line =~ /SMARTOLDERROR\[([\w\/]+)\]\s+(\d+)/)
+        {
+           $olderr{$1} = $2;
+        }
+        if ($line =~ /SMARTCACHETIME=(\d+)/)
+        {
+           $CACHETIME = $1;
+        }
+    }
+    close C;
+}
diff --git a/xymon/plugins/client/ext/smartoverall b/xymon/plugins/client/ext/smartoverall
new file mode 100755
index 0000000..680e7b6
--- /dev/null
+++ b/xymon/plugins/client/ext/smartoverall
@@ -0,0 +1,300 @@
+#!/bin/sh
+# .. vim: foldmarker=[[[,]]]:foldmethod=marker
+
+# NOTE: Must be run as root, so you probably need to setup sudo for this.
+
+# This script is mostly intend to be used with Xymon and rather for devices unknown to the smartmontools base.
+# Based on xymon.com's script : https://www.xymon.com/xymon-cgi/viewconf.sh?smart
+# The script will scan all devices compatible with SMART and for each disk, it will : [[[
+#	* try to guess the expected TYPE (even megaraid,…).
+#	* display health status.
+#	* set a "clear" state for incompatible device.
+#	* display last selftests.
+#	* set a "error" state if no selftest is recorded.
+#	* display basic informations.
+#	* recommend a more advanced SMART script if the disk is known of smartmontools's database (drivedb.h) or redirect to smartmontools's FAQ if not.
+# ]]]
+# Things the script CAN'T do : [[[
+#	* ensure a recent selftest was run.
+#	* compare current value with vendor's one (for failure prediction or error).
+#	* give detail about errors.
+#	* Take a look to this more advance script for such features : https://github.com/skazi0/xymon-plugins/blob/master/client/ext/smart
+# ]]]
+
+# Vars [[[
+debug="1"
+
+## Colors [[[
+c_redb='\033[1;31m'
+c_magentab='\033[1;35m'
+c_reset='\033[0m'
+## ]]]
+
+plugin_name=$(basename "${0}")
+
+plugin_result="${XYMONTMP}/${MACHINEDOTS}.smartoverall.plugin_result"
+plugin_state="${XYMONTMP}/${MACHINEDOTS}.smartoverall.plugin_state"
+device_list="${XYMONTMP}/${MACHINEDOTS}.smartoverall.dscan"
+## List of devices known from the smartmontools base and compatible with test logging
+## This file might be used by a more advanced script such as skazi0's one
+drivedb_list="${XYMONTMP}/${MACHINEDOTS}.smart.drivedb.list"
+
+# By default, don't empty files newer than 10hours (600 minutes)
+default_mtime_minutes="600"
+
+xymon_username="xymon"
+xymon_groupname="xymon"
+# ]]]
+
+# Functions
+## Create or empty a file if it's too old [[[
+## First argument (required): Absolut path to the file
+## Second argument (optionnal): Maximum number of minutes since last modification
+regenerate_if_too_old() {
+	## Set variables according to the number of passed arguments [[[
+	case $# in
+		0 )
+			[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Need at least 1 argument."
+			exit 1
+			;;
+		1 )
+			_file="${1}"
+			[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Use default_mtime_minutes value: ${default_mtime_minutes}."
+			_max_mtime_minutes="${default_mtime_minutes}"
+			;;
+		2 )
+			_file="${1}"
+			_max_mtime_minutes="${2}"
+			;;
+	esac
+	## ]]]
+	_current_timestamp=$(date "+%s")
+	_file_mtime_timestamp=$(stat --format="%Y" -- "${_file}")
+
+	## Substract last modification timestamp of the file to current timestamp
+	: $(( _file_mtime_seconds=_current_timestamp-_file_mtime_timestamp ))
+	## Get maximum allowed mtime in seconds
+	: $(( _max_mtime_seconds=_max_mtime_minutes*60 ))
+
+	## Compare last modification mtime with the maximum allowed
+	if [ "${_file_mtime_seconds}" -gt "${_max_mtime_seconds}" ]; then
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Need to empty or create ${_file} last modification happened ${_file_mtime_seconds} seconds ago (maximum is ${_max_mtime_seconds})."
+		true > "${_file}"
+		chown -- "${xymon_username}":"${xymon_groupname}" "${_file}"
+	else
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Don't need to empty ${_file} last modification happened ${_file_mtime_seconds} seconds ago (maximum is ${_max_mtime_seconds})."
+	fi
+
+}
+## ]]]
+## Test if a disk really support SMART [[[
+## Smartctl can give an health status even without a full support
+## of SMART for some type (eg. scsi or megaraid).
+## Exemple : SMART support is: Unavailable - device lacks SMART capability.
+is_disk_support_smart() {
+	_disk="${1}"
+	_type="${2}"
+
+	_smarctl_support_result="${XYMONTMP}/${MACHINEDOTS}.smartoverall.support.$(basename "${_disk}").${_type}"
+
+	smart_support_msg=""
+
+	[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : is_disk_support_smart func − check if SMART is supported on : ${_disk}."
+
+	## Create or empty previous file only if older than 24h (1440 minutes)
+	regenerate_if_too_old "${_smarctl_support_result}" 1440
+
+	## Grep only "support" lines from disk's informations only if the file was emptied
+	if test ! -s "${_smarctl_support_result}"; then
+		smartctl -d "${_type}" -i -- "${_disk}" | grep -E "^SMART support is:" -- >> "${_smarctl_support_result}"
+	fi
+
+	## If the file is not empty
+	if test -s "${_smarctl_support_result}"; then
+		## Parse all "support" lines
+		while IFS= read -r _LINE; do
+			if ! printf -- '%s' "${_LINE}" | grep -q -E -- "(Enabled|Available)"
+			then
+				smart_support_msg="${_LINE}"
+			fi
+		done < "${_smarctl_support_result}"
+	else
+		smart_support_msg="smartctl was not able to open ${_disk} DEVICE with ${_type} TYPE."
+	fi
+
+	if [ -z "${smart_support_msg}" ]; then
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : is_disk_support_smart func − SMART seems fully supported on : ${_disk} with ${_type} type."
+	else
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : is_disk_support_smart func − SMART is not fully supported on : ${_disk} with ${_type} type. See smartctl informations :\n${smart_support_msg}"
+	fi
+
+## Clean temp files
+### As the Xymon's tmpdir is used to store log files, no need to delete them at
+### the end of the script. They will be emptied, reused or regenerate (if oldest
+### than the expected interval) at the next run.
+
+}
+## ]]]
+## Test the type of disk with smartctl [[[
+## Cause the scanned one might not be the one to use
+choose_correct_type() {
+	_disk="${1}"
+	_scanned_type="${2}"
+	_default_type="auto"
+
+	TYPE=""
+	SMART_SUPPORT_MSG=""
+
+	for test_type in "${_scanned_type}" "${_default_type}"; do
+		is_disk_support_smart "${_disk}" "${test_type}"
+
+		## If no message, the type is correct
+		if [ -z "${smart_support_msg}" ]; then
+			TYPE="${test_type}"
+			SMART_SUPPORT_MSG=""
+			return
+		else
+			SMART_SUPPORT_MSG="${smart_support_msg}"
+		fi
+
+	done
+
+}
+## ]]]
+
+# Create or empty previous files
+true > "${plugin_result}"
+chown -- "${xymon_username}":"${xymon_groupname}" "${plugin_result}"
+true > "${plugin_state}"
+chown -- "${xymon_username}":"${xymon_groupname}" "${plugin_state}"
+## Create or empty previous file only if older than 24h (1440 minutes)
+regenerate_if_too_old "${device_list}" 1440
+regenerate_if_too_old "${drivedb_list}" 1440
+
+# Get the list of all available devices if the previous list was emptied
+if test ! -s "${device_list}"; then
+	smartctl --scan >> "${device_list}"
+fi
+
+# If the file is not empty
+if test -s "${device_list}"; then
+	while IFS= read -r LINE; do
+		## Get device path
+		DISK=$(echo "${LINE}" | cut -d" " -f1)
+		## Try to determine the best type
+		SCANNED_TYPE=$(echo "${LINE}" | cut -d" " -f3)
+		choose_correct_type "${DISK}" "${SCANNED_TYPE}"
+
+		## If no correct type was found for this device
+		if [ -z "${TYPE}" ]; then
+			[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : SMART is not fully supported."
+			DRES=$(printf '%s' "SMART Health Status can't be determine because of:\n${SMART_SUPPORT_MSG}")
+			DCODE="2"
+			TYPE="unsupported"
+			### Still try to display informations about unsupported device (eg. RAID controller,…)
+			DID="unsupported-${DISK}"
+			DINFO=$(smartctl -i -d "${SCANNED_TYPE}" "${DISK}" | grep -v -E "^smartctl|^Copyright|^$" || printf '%s' "Can't get informations due to no SMART support.")
+			DDRIVEDB_MSG=""
+			DSELFTEST=""
+		else
+			[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : SMART seems fully supported, proceed normally."
+			### Get SMART Health Status and return code
+			DRES=$(/usr/sbin/smartctl -H -d "${TYPE}" -n standby "${DISK}")
+			DCODE=$?
+			### Get disk's serial number and informations
+			DID=$(smartctl -i -d "${TYPE}" "${DISK}" | awk '/.erial .umber:/ { print $NF }')
+			DINFO=$(smartctl -i -d "${TYPE}" "${DISK}" | grep -v -E "^smartctl|^Copyright|^$")
+
+			## If the model of the disk is known from smartmontools database
+			if smartctl -d "${TYPE}" -P show "${DISK}" | grep -qi -- "drive found in"; then
+				DDRIVEDB_MSG="&green Device is known in smartmontools database. You might consider using a more advanced plugin such as:
+https://github.com/skazi0/xymon-plugins/blob/master/client/ext/smart"
+			else
+				DDRIVEDB_MSG="&clear Device is unknown or not complete in smartmontools database. Please take a look to the FAQ:
+https://www.smartmontools.org/wiki/FAQ#SmartmontoolsDatabase"
+			fi
+
+			DSELFTEST=$(smartctl -d "${TYPE}" -l selftest "${DISK}" | grep -v -E -- "^smartctl|^Copyright|^$")
+			## If no selftest have been recorded
+			if smartctl -d "${TYPE}" -l selftest "${DISK}" | grep -qi -- "No self-tests"; then
+				DSELFTEST_MSG="&red No self-tests recorded:"
+				DCODE="8"
+			## If the device doesn't support test logging
+			elif smartctl -d "${TYPE}" -l selftest "${DISK}" | grep -qEi -- "(does not support.*logging|Log not supported)"; then
+				DSELFTEST_MSG="&clear Test logging are not supported:"
+			else
+				DSELFTEST_MSG=""
+				### If the device is also known from smartmontools database
+				###    and not already present in the list of compatible disk
+				if printf -- '%s' "${DDRIVEDB_MSG}" | grep -q -E -- "green" &&
+					! grep -q -- "${DISK}" "${drivedb_list}"
+				then
+					echo "${DISK}" >> "${drivedb_list}"
+				fi
+			fi
+		fi
+
+		## Test health status
+		DSTBY=$(( DCODE & 2 ))
+		DFAIL=$(( DCODE & 8 ))
+		DWARN=$(( DCODE & 32 ))
+
+		## According to health, give a weight to each color to easily get the page status
+		if test $DSTBY -ne 0
+		then
+			COLOR="4&clear"
+		elif test $DFAIL -ne 0
+		then
+			COLOR="1&red"
+		elif test $DWARN -ne 0
+		then
+			COLOR="2&yellow"
+		else
+			COLOR="3&green"
+		fi
+
+		## Avoid duplicate device
+		if ! grep -q "${DID}" "${plugin_result}"; then
+			## For summary
+			echo "${COLOR} $DISK ${TYPE}"
+
+			## For detailed informations
+			{
+				echo "${COLOR} $DISK ${TYPE}" | cut -c2-
+				echo ""
+				echo "$DRES" | grep -v -E "^smartctl|^Copyright|^$|^==="
+				echo "${DDRIVEDB_MSG}"
+				echo "${DINFO}"
+				echo "${DSELFTEST_MSG}"
+				echo "${DSELFTEST}" | head -n12
+				echo "------------------------------------------------------------"
+				echo ""
+				echo ""
+			} >> "${plugin_result}"
+	fi
+	done < "${device_list}" >> "${plugin_state}"
+
+# If the file is empty
+else
+	echo "1&red Error while scanning devices with smartctl" >> "${plugin_state}"
+fi
+
+# Set the global color according to the highest alert
+COLOR=$(< "${plugin_state}" awk '{print $1}' | sort | uniq | head -1 | cut -c3-)
+
+# Send informations to Xymon server
+$XYMON "${XYMSRV}" "status ${MACHINE}.${plugin_name} ${COLOR} SMART health check
+
+$(< "${plugin_state}" cut -c2-)
+
+==================== Detailed status ====================
+
+$(cat "${plugin_result}")
+"
+
+## Clean temp files
+### As the Xymon's tmpdir is used to store log files, no need to delete them at
+### the end of the script. They will be emptied, reused or regenerate (if oldest
+### than the expected interval) at the next run.
+
+exit 0
diff --git a/xymon/plugins/client/ext/test.int.compare.sh b/xymon/plugins/client/ext/test.int.compare.sh
new file mode 100755
index 0000000..3e0403c
--- /dev/null
+++ b/xymon/plugins/client/ext/test.int.compare.sh
@@ -0,0 +1,66 @@
+#!/bin/sh
+# .. vim: foldmarker=[[[,]]]:foldmethod=marker
+
+# Vars [[[
+debug="0"
+
+## Colors [[[
+c_redb='\033[1;31m'
+c_magentab='\033[1;35m'
+c_reset='\033[0m'
+## ]]]
+default_mtime_minutes="600"
+
+drivedb_list="/tmp/test.css"
+
+DDRIVEDB_MSG="green"
+#DDRIVEDB_MSG="red"
+DISK="/dev/sda"
+# ]]]
+## Create or empty a file if it's too old [[[
+regenerate_if_too_old() {
+	## Set variables according to the number of passed arguments
+	case $# in
+		1 )
+			_file="${1}"
+			[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Use default_mtime_minutes value: ${default_mtime_minutes}."
+			_max_mtime_minutes="${default_mtime_minutes}"
+			;;
+		2 )
+			_file="${1}"
+			_max_mtime_minutes="${2}"
+			;;
+	esac
+
+	_current_timestamp=$(date "+%s")
+	_file_mtime_timestamp=$(stat --format="%Y" -- "${_file}")
+
+	## Substract last modification timestamp of the file to current timestamp
+	: $(( _file_mtime_seconds=_current_timestamp-_file_mtime_timestamp ))
+	## Get maximum allowed mtime in seconds
+	: $(( _max_mtime_seconds=_max_mtime_minutes*60 ))
+
+	## Compare last modification mtime with the maximum allowed
+	if [ "${_file_mtime_seconds}" -gt "${_max_mtime_seconds}" ]; then
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Need to empty or create ${_file} last modification happened ${_file_mtime_seconds} seconds ago (maximum is ${_max_mtime_seconds})."
+		true > "${_file}"
+	else
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : regenerate_if_too_old func − Don't need to empty ${_file} last modification happened ${_file_mtime_seconds} seconds ago (maximum is ${_max_mtime_seconds})."
+	fi
+
+}
+## ]]]
+
+regenerate_if_too_old /tmp/css_style.css
+regenerate_if_too_old /tmp/font.css 60
+regenerate_if_too_old /tmp/user/1337/serverauth.qGdeK8OOzr 1440
+regenerate_if_too_old /tmp/test.css 600
+
+if printf -- '%s' "${DDRIVEDB_MSG}" | grep -q -E -- "green" &&
+   ! grep -q -- "${DISK}" "${drivedb_list}"
+then
+	echo "${DISK}" >> "${drivedb_list}"
+				fi
+
+
+exit 0
diff --git a/xymon/sample.messages/apt.alert b/xymon/sample.messages/apt.alert
new file mode 100644
index 0000000..2b586f0
--- /dev/null
+++ b/xymon/sample.messages/apt.alert
@@ -0,0 +1,28 @@
+BBCOLORLEVEL="red"
+BBALPHAMSG="HOST.DOMAIN.ORG:apt red [168321]
+red Wed Aug 22 11:26:34 2018 - apt NOT ok
+Debian GNU/Linux 9.5 (stretch)
+
+&red Security updates (4): apt-get install openssh-client openssh-server openssh-sftp-server ssh
+   openssh-client (1:7.4p1-10+deb9u3 1:7.4p1-10+deb9u4)
+   openssh-server (1:7.4p1-10+deb9u3 1:7.4p1-10+deb9u4)
+   openssh-sftp-server (1:7.4p1-10+deb9u3 1:7.4p1-10+deb9u4)
+   ssh (1:7.4p1-10+deb9u3 1:7.4p1-10+deb9u4)
+
+&red Last apt update: 3.0 day(s) ago
+
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=apt
+"
+ACKCODE="168321"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="apt"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.apt"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.apt"
+BBNUMERIC="000111222333444168321"
+RECOVERED="0"
+DOWNSECS="36"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/cpu.alert b/xymon/sample.messages/cpu.alert
new file mode 100644
index 0000000..4eb1c79
--- /dev/null
+++ b/xymon/sample.messages/cpu.alert
@@ -0,0 +1,62 @@
+BBCOLORLEVEL="yellow"
+BBALPHAMSG="HOST.DOMAIN.ORG:cpu yellow [520216]
+yellow Tue Aug 21 11:43:22 CEST 2018 up: 00:00, 0 users, 29 procs, load=1.90
+&yellow Machine recently rebooted
+System clock is 0 seconds off
+
+
+top - 11:43:23 up 0 min,  0 users,  load average: 1.49, 1.90, 3.03
+Tasks:  33 total,   2 running,  31 sleeping,   0 stopped,   0 zombie
+%Cpu(s):  3.8 us,  5.9 sy,  0.0 ni, 89.3 id,  0.8 wa,  0.0 hi,  0.1 si,  0.0 st
+KiB Mem :  1048576 total,   897468 free,    33268 used,   117840 buff/cache
+KiB Swap:  1048576 total,  1048576 free,        0 used.  1015308 avail Mem
+
+   PID USER      PR  NI    VIRT    RES    SHR S  %CPU %MEM     TIME+ COMMAND
+   263 xymon     20   0   64284   6264   5072 D 100.0  0.6   0:00.05 apt-cache
+     1 root      20   0   69588   7680   5968 S   0.0  0.7   0:00.08 systemd
+    43 root      20   0   93256  16952  16356 S   0.0  1.6   0:00.03 systemd-j+
+    89 root      20   0   22560   1052      0 S   0.0  0.1   0:00.00 dhclient
+   121 root      20   0   29668   2804   2520 S   0.0  0.3   0:00.00 cron
+   122 root      20   0  321836   2756   2348 S   0.0  0.3   0:00.00 rsyslogd
+   124 root      20   0  171944   9704   8308 S   0.0  0.9   0:00.00 sssd
+   130 message+  20   0   59424   4036   3576 S   0.0  0.4   0:00.00 dbus-daem+
+   145 daemon    20   0   27968   2120   1916 S   0.0  0.2   0:00.00 atd
+   147 root      20   0   71988   5648   4896 S   0.0  0.5   0:00.00 sshd
+   164 xymon     20   0    4272   1488   1332 S   0.0  0.1   0:00.00 xymonlaun+
+   167 xymon     20   0    4292    712    640 S   0.0  0.1   0:00.00 xymonclie+
+   168 xymon     20   0   18300   5152   3940 S   0.0  0.5   0:00.00 apt
+   176 root      20   0  201132  15804  10264 S   0.0  1.5   0:00.02 sssd_be
+   177 root      20   0   17076    160      0 S   0.0  0.0   0:00.00 in.tftpd
+   191 root      20   0  168252  33204  32060 S   0.0  3.2   0:00.02 sssd_nss
+   192 root      20   0  147780   7452   6396 S   0.0  0.7   0:00.00 sssd_pam
+   193 root      20   0  141356   7364   6344 S   0.0  0.7   0:00.00 sssd_auto+
+   198 xymon     20   0    4292   1360   1252 S   0.0  0.1   0:00.00 xymonclie+
+   211 arpwatch  20   0   31872   4792   4104 S   0.0  0.5   0:00.00 arpwatch
+   214 root      20   0   54532   2768   2276 S   0.0  0.3   0:00.00 systemd-l+
+   223 root      20   0   69592   1716      4 S   0.0  0.2   0:00.00 (agetty)
+   224 root      20   0   69592   1716      4 S   0.0  0.2   0:00.00 (agetty)
+   251 root      20   0  361140  15748   6296 S   0.0  1.5   0:00.04 fail2ban-+
+   292 root      20   0   81152   6396   5636 S   0.0  0.6   0:00.00 postmulti
+   298 root      20   0    4292    752    680 S   0.0  0.1   0:00.00 postfix-s+
+   306 xymon     20   0   38236   2984   2584 R   0.0  0.3   0:00.00 top
+   345 root      20   0    4292    712    636 S   0.0  0.1   0:00.00 sh
+   349 root      20   0   22536   1392   1164 D   0.0  0.1   0:00.00 nft
+   351 root      20   0    4292    760    688 S   0.0  0.1   0:00.00 postfix-s+
+   353 root      20   0    4292     96      0 S   0.0  0.0   0:00.00 postfix-s+
+   354 root      20   0   79236   4740   4064 R   0.0  0.5   0:00.00 postconf
+   355 root      20   0   13216   1004    900 S   0.0  0.1   0:00.00 sed
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=cpu
+"
+ACKCODE="520216"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="cpu"
+BBSVCNUM="200"
+BBHOSTSVC="HOST.DOMAIN.ORG.cpu"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.cpu"
+BBNUMERIC="200111222333444520216"
+RECOVERED="0"
+DOWNSECS="0"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/files.alert b/xymon/sample.messages/files.alert
new file mode 100644
index 0000000..2a4ccd9
--- /dev/null
+++ b/xymon/sample.messages/files.alert
@@ -0,0 +1,41 @@
+BBCOLORLEVEL="yellow"
+BBALPHAMSG="HOST.DOMAIN.ORG:files yellow [275849]
+yellow Thu Oct 10 11:17:18 CEST 2019 - Files NOT ok
+
+&yellow <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/var/log/cron.log">/var/log/cron.log</a>
+File was modified 4642 seconds ago - should be <3800
+
+&yellow <a href="/xymon-cgi/svcstatus.sh?CLIENT=vmgit.101010.virtual&amp;SECTION=file:/tmp/.github.TEST.upgrade">/tmp/.github.TEST.upgrade</a>
+File exists
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=logfile:/var/log/kern.log">/var/log/kern.log</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/var/log/messages">/var/log/messages</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/var/log/syslog">/var/log/syslog</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=dir:/var/log">/var/log</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=dir:/tmp/">/tmp/</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/bin/su">/bin/su</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/usr/bin/sudo">/usr/bin/sudo</a>
+
+&green <a href="/xymon-cgi/svcstatus.sh?CLIENT=HOST.DOMAIN.ORG&amp;SECTION=file:/var/log/installer">/var/log/installer</a>
+
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=files
+"
+ACKCODE="275849"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="037187001062"
+BBSVCNAME="files"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.files"
+BBHOSTSVCCOMMAS="HOST,DOMAIN.ORG.files"
+BBNUMERIC="000037187001062275849"
+RECOVERED="0"
+DOWNSECS="603"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/libs.alert b/xymon/sample.messages/libs.alert
new file mode 100644
index 0000000..3c98eea
--- /dev/null
+++ b/xymon/sample.messages/libs.alert
@@ -0,0 +1,29 @@
+BBCOLORLEVEL="yellow"
+BBALPHAMSG="HOST.DOMAIN.ORG:libs yellow [0]
+yellow Thu Aug 16 16:41:56 2018 - libs NOT ok
+&yellow Machine should be rebooted. Running not the newest installed kernel:
+
+  Running kernel=\"4.9.0-7-amd64, version #1 SMP Debian 4.9.110-3+deb9u1 (2018-08-03)\"
+  Newest installed kernel=\"4.9.0-7-amd64, version #1 SMP Debian 4.9.110-3+deb9u2 (2018-08-13)\"
+
+&yellow The following processes have libs linked that were upgraded:
+
+root:
+  /lib/systemd/systemd-udevd (546)
+systemd-timesync:
+  /usr/lib/postfix/qmgr (52880)
+
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=libs"
+ACKCODE="0"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="libs"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.libs"
+BBHOSTSVCCOMMAS="HOST.DOMAIN.ORG.libs"
+BBNUMERIC="0001112223334440"
+RECOVERED="0"
+DOWNSECS="36320"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/memory.alert b/xymon/sample.messages/memory.alert
new file mode 100644
index 0000000..953b69a
--- /dev/null
+++ b/xymon/sample.messages/memory.alert
@@ -0,0 +1,22 @@
+BBCOLORLEVEL="red"
+BBALPHAMSG="HOST.DOMAIN.ORG:memory red [251314]
+red Tue Aug 21 11:42:42 CEST 2018 - Memory CRITICAL
+   Memory                  Used       Total  Percentage
+&green Real/Physical          1017M       1536M         66%
+&green Actual/Virtual          692M       1536M         45%
+&red Swap/Page              1024M       1024M        100%
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=memory
+"
+ACKCODE="251314"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="memory"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.memory"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.memory"
+BBNUMERIC="000111222333444251314"
+RECOVERED="0"
+DOWNSECS="0"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/ntpq.alert b/xymon/sample.messages/ntpq.alert
new file mode 100644
index 0000000..ed8d9cb
--- /dev/null
+++ b/xymon/sample.messages/ntpq.alert
@@ -0,0 +1,38 @@
+BBCOLORLEVEL="red"
+BBALPHAMSG="HOST.DOMAIN.ORG:ntpq red [842850]
+red Tue Aug 21 11:20:53 2018 - ntpq NOT ok
+NTP peers:
+
+        remote             refid      st t when poll reach   delay   offset  jitter
+   ==============================================================================
+&clear  WWW.XXX.YYY.ZZZ   213.251.53.11    3 u   18   64    1    0.542   -2.836   0.000
+
+&red No system peer entry ("*") found
+
+        remote           refid      st t when poll reach   delay   offset  jitter
+   ==============================================================================
+&green *WWW.XXX.YYY.ZZZ   51.15.178.157    3 u  243 1024  377    1.194  102.549  83.035
+
+SyspeerDelay: 1.194
+SyspeerOffset: 102.549
+SyspeerJitter: 83.035
+
+SyspeerOffset thresholds:
+Warning: 100ms
+Critical: 2000ms
+&yellow SyspeerOffset > 100ms
+
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=ntpq
+"
+ACKCODE="842850"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="ntpq"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.ntpq"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.ntpq"
+BBNUMERIC="000111222333444842850"
+RECOVERED="0"
+DOWNSECS="1544"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/ports.alert b/xymon/sample.messages/ports.alert
new file mode 100644
index 0000000..61caeef
--- /dev/null
+++ b/xymon/sample.messages/ports.alert
@@ -0,0 +1,31 @@
+BBCOLORLEVEL="yellow"
+BBALPHAMSG="HOST.DOMAIN.ORG:ports yellow [40450]
+yellow Tue Aug 21 11:43:22 CEST 2018 - Ports NOT ok
+&yellow SMTP listener (found 0, req. between 1 and 2)
+&green SSH logins (found 0, req. at most 10)
+&green Bad listeners (found 0, req. at most 0)
+
+Active Internet connections (servers and established)
+Proto Recv-Q Send-Q Local Address           Foreign Address         State
+tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN
+tcp        0      0 111.222.333.444:45250     WWW.XXX.YYY.ZZZ:1984     TIME_WAIT
+tcp        0      0 111.222.333.444:54522     444.333.222.111:389        ESTABLISHED
+tcp        0      0 111.222.333.444:45244     WWW.XXX.YYY.ZZZ:1984     TIME_WAIT
+tcp        0      0 111.222.333.444:45242     WWW.XXX.YYY.ZZZ:1984     TIME_WAIT
+tcp6       0      0 :::22                   :::*                    LISTEN
+udp        0      0 0.0.0.0:68              0.0.0.0:*
+udp6       0      0 :::69                   :::*
+See http://localhost/xymon-cgi/svcstatus.sh?HOST=HOST.DOMAIN.ORG&SERVICE=ports
+"
+ACKCODE="40450"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="ports"
+BBSVCNUM="0"
+BBHOSTSVC="HOST.DOMAIN.ORG.ports"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.ports"
+BBNUMERIC="00011122233344440450"
+RECOVERED="0"
+DOWNSECS="6"
+DOWNSECSMSG=""
diff --git a/xymon/sample.messages/procs.alert b/xymon/sample.messages/procs.alert
new file mode 100644
index 0000000..186475d
--- /dev/null
+++ b/xymon/sample.messages/procs.alert
@@ -0,0 +1,71 @@
+BBCOLORLEVEL="red"
+BBALPHAMSG="HOST.DOMAIN.ORG:procs red [757744]
+red Tue Aug 21 13:29:28 CEST 2018 - Processes NOT ok
+&green systemd-journald (found 1, req. between 1 and 1)
+&green systemd-logind (found 1, req. between 1 and 1)
+&green CRON (found 1, req. between 1 and 999)
+&green ATD (found 1, req. between 1 and 999)
+&green MTA-Stretch (found 1, req. between 1 and 1)
+&green SSHD (found 3, req. between 1 and 20)
+&green SSSD (found 1, req. between 1 and 1)
+&green Fail2Ban (found 1, req. between 1 and 1)
+&red tftpd-hpa (found 0, req. between 1 and 1)
+&yellow ARPwatch (found 0, req. between 1 and 1)
+&red Jenkins (found 0, req. between 1 and 5)
+
+   PID   PPID USER      STARTED S PRI %CPU         TIME %MEM        RSZ        VSZ CMD
+     1      0 root     11:43:19 S  19  0.0     00:00:00  0.7       7816      69724 /sbin/init
+    43      1 root     11:43:20 S  19  0.0     00:00:00  2.4      25848     109744 /lib/systemd/systemd-journald
+    89      1 root     11:43:20 S  19  0.0     00:00:00  0.1       1052      22560 /sbin/dhclient -4 -v -pf /run/dhclient.eth0.pid -lf /var/lib/dhcp/dhclient.eth0.leases -I -df /var/lib/dhcp/dhclient6.eth0.leases eth0
+   121      1 root     11:43:21 S  19  0.0     00:00:00  0.2       2804      29668 /usr/sbin/cron -f
+   122      1 root     11:43:21 S  19  0.0     00:00:00  0.2       2756     321836 /usr/sbin/rsyslogd -n
+   124      1 root     11:43:21 S  19  0.0     00:00:00  0.9       9704     171944 /usr/sbin/sssd -i -f
+   176    124 root     11:43:21 S  19  0.0     00:00:00  1.7      18244     212360  \_ /usr/lib/x86_64-linux-gnu/sssd/sssd_be --domain ur1 --uid 0 --gid 0 --debug-to-files
+   191    124 root     11:43:21 S  19  0.0     00:00:00  3.1      33204     168252  \_ /usr/lib/x86_64-linux-gnu/sssd/sssd_nss --uid 0 --gid 0 --debug-to-files
+   192    124 root     11:43:21 S  19  0.0     00:00:00  0.8       8672     147912  \_ /usr/lib/x86_64-linux-gnu/sssd/sssd_pam --uid 0 --gid 0 --debug-to-files
+   193    124 root     11:43:21 S  19  0.0     00:00:00  0.7       7364     141356  \_ /usr/lib/x86_64-linux-gnu/sssd/sssd_autofs --uid 0 --gid 0 --debug-to-files
+   145      1 daemon   11:43:21 S  19  0.0     00:00:00  0.2       2120      27968 /usr/sbin/atd -f -l 9.6 -b 98
+   147      1 root     11:43:21 S  19  0.0     00:00:00  0.5       6180      71988 /usr/sbin/sshd -D
+  4810    147 root     13:29:14 S  19  0.0     00:00:00  0.7       7468     134176  \_ sshd: USER [priv]
+  5023   4810 USER 13:29:14 S  19  0.0     00:00:00  0.3       3952     134176      \_ sshd: USER@pts/2
+  5024   5023 USER 13:29:14 S  19  0.0     00:00:00  0.5       5608      59296          \_ zsh
+  5057   5024 USER 13:29:15 S  19  0.0     00:00:00  0.2       2988      19336              \_ tmux
+   223      1 root     11:43:21 S  19  0.0     00:00:00  0.1       2060      14316 /sbin/agetty -o -p -- \u --noclear --keep-baud tty1 115200,38400,9600 linux
+   224      1 root     11:43:21 S  19  0.0     00:00:00  0.1       2056      14316 /sbin/agetty -o -p -- \u --noclear --keep-baud console 115200,38400,9600 linux
+   251      1 root     11:43:22 S  19  0.0     00:00:01  1.5      15800     361140 /usr/bin/python3 /usr/bin/fail2ban-server -s /var/run/fail2ban/fail2ban.sock -p /var/run/fail2ban/fail2ban.pid -x -b
+   412      1 root     11:43:22 S  19  0.0     00:00:00  0.4       4244      83252 /usr/lib/postfix/sbin/master -w
+   415    412 postfix  11:43:22 S  19  0.0     00:00:00  0.6       6628      95528  \_ qmgr -l -t unix -u
+  4453    412 postfix  13:19:59 S  19  0.0     00:00:00  0.6       6532      95480  \_ showq -t unix -u -c
+  4504    412 postfix  13:23:22 S  19  0.0     00:00:00  0.6       6524      95480  \_ pickup -l -t unix -u -c
+   416      1 netdata  11:43:22 S  19  0.0     00:02:06  7.1      75324     224012 /usr/sbin/netdata -D
+   432    416 netdata  11:43:23 R  19  0.0     00:00:16  0.2       2628      28108  \_ /usr/lib/x86_64-linux-gnu/netdata/plugins.d/apps.plugin 1
+   433    416 netdata  11:43:23 S  19  0.0     00:01:30  4.6      48576     121208  \_ /usr/bin/python /usr/lib/x86_64-linux-gnu/netdata/plugins.d/python.d.plugin 1
+  4643    416 netdata  13:25:26 S  19  0.0     00:00:00  0.2       2688       9700  \_ bash /usr/lib/x86_64-linux-gnu/netdata/plugins.d/tc-qos-helper.sh 1
+   660      1 xymon-s+ 11:43:27 S  19  0.0     00:00:00  0.6       6788      68928 /lib/systemd/systemd --user
+   662    660 xymon-s+ 11:43:27 S  19  0.0     00:00:00  0.1       1904     123912  \_ (sd-pam)
+   881      1 message+ 11:43:27 S  19  0.0     00:00:00  0.4       4384      67636 /usr/bin/dbus-daemon --system --address=systemd: --nofork --nopidfile --systemd-activation
+   883      1 root     11:43:27 S  19  0.0     00:00:00  0.5       5552      73268 /lib/systemd/systemd-logind
+  1377      1 USER 11:49:11 S  19  0.0     00:00:00  0.6       6716      68932 /lib/systemd/systemd --user
+  1379   1377 USER 11:49:11 S  19  0.0     00:00:00  0.1       2040     132260  \_ (sd-pam)
+  4768      1 xymon    13:28:48 S  19  0.0     00:00:00  0.0        756       4292 sh -c vmstat 300 2 1&gt;/var/lib/xymon/tmp/xymon_vmstat.HOST.DOMAIN.ORG.4719 2&gt;&amp;1; mv /var/lib/xymon/tmp/xymon_vmstat.HOST.DOMAIN.ORG.4719 /var/lib/xymon/tmp/xymon_vmstat.HOST.DOMAIN.ORG
+  4770   4768 xymon    13:28:48 S  19  0.0     00:00:00  0.1       1400      24900  \_ vmstat 300 2
+  5059      1 USER 13:29:15 S  19  0.0     00:00:00  0.3       3364      28044 tmux
+  5067   5059 USER 13:29:15 S  19  0.0     00:00:00  0.6       6396      62052  \_ -zsh
+  5187      1 xymon    13:29:27 S  19  0.0     00:00:00  0.1       1576       4272 /usr/lib/xymon/client/bin/xymonlaunch --config=/etc/xymon/clientlaunch.cfg --log=/var/log/xymon/clientlaunch.log --pidfile=/var/run/xymon/clientlaunch.pid
+  5191   5187 xymon    13:29:27 S  19  0.0     00:00:00  0.1       1572       4292  \_ /bin/sh /usr/lib/xymon/client/bin/xymonclient.sh
+  5214   5191 xymon    13:29:27 S  19  0.0     00:00:00  0.1       1600       4292  |   \_ /bin/sh /usr/lib/xymon/client/bin/xymonclient-linux.sh
+  5256   5214 xymon    13:29:28 R  19  0.0     00:00:00  0.2       2804      44404  |       \_ ps -Aww f -o pid,ppid,user,start,state,pri,pcpu,time:12,pmem,rsz:10,vsz:10,cmd
+  5192   5187 xymon    13:29:27 S  19  0.0     00:00:00  0.4       5164      18300  \_ /usr/bin/perl -w /usr/lib/xymon/client/ext/apt
+  5231   5192 xymon    13:29:28 R  19  0.0     00:00:00  3.9      41128      70068      \_ apt-cache policy acl adduser apt apt-listchanges apt-transport-https apt-utils aptitude aptitude-common arpwatch at base-files base-passwd bash bash-completion bind9-host binutils bsd-mailx bsdmainutils bsdutils bzip2 ca-certificates coreutils cpio cpp cpp-6 cracklib-runtime cron curl dash dbus dctrl-tools debconf debconf-i18n debian-archive-keyring debian-faq debian-goodies debianutils debsecan debsums dh-python diffutils dirmngr distro-info-data dmidecode dmsetup doc-debian dpkg e2fslibs:amd64 e2fsprogs ed etckeeper fail2ban file findutils fontconfig-config fonts-dejavu-core fonts-font-awesome fping gcc-6-base:amd64 gettext-base git git-man gnupg gnupg-agent gnutls-bin gpgv grep groff-base gzip hobbit-plugins hostname htop iftop ifupdown init init-system-helpers DOMAINoute2 iputils-ping isc-dhcp-client isc-dhcp-common kmod krb5-locales less libacl1:amd64 libapparmor1:amd64 libapt-inst2.0:amd64 libapt-pkg5.0:amd64 libasprintf0v5:amd64 libassuan0:amd64 libattr1:amd64 libaudit-common libaudit1:amd64 libavahi-client3:amd64 libavahi-common-data:amd64 libavahi-common3:amd64 libbasicobjects0:amd64 libbind9-140:amd64 libblkid1:amd64 libboost-filesystem1.62.0:amd64 libboost-iostreams1.62.0:amd64 libboost-system1.62.0:amd64 libbsd0:amd64 libbz2-1.0:amd64 libc-ares2:amd64 libc-bin libc-l10n libc6:amd64 libcap-ng0:amd64 libcap2-bin libcap2:amd64 libclass-isa-perl libcollection4:amd64 libcomerr2:amd64 libcrack2:amd64 libcryptsetup4:amd64 libcups2:amd64 libcurl3-gnutls:amd64 libcurl3:amd64 libcwidget3v5:amd64 libdb5.3:amd64 libdbus-1-3:amd64 libdebconfclient0:amd64 libdevmapper1.02.1:amd64 libdhash1:amd64 libdns-export162 libdns162:amd64 libdpkg-perl libdrm2:amd64 libedit2:amd64 libelf1:amd64 liberror-perl libes"
+ACKCODE="757744"
+RCPT="1234567890"
+BBHOSTNAME="HOST.DOMAIN.ORG"
+MACHIP="111222333444"
+BBSVCNAME="procs"
+BBSVCNUM="300"
+BBHOSTSVC="HOST.DOMAIN.ORG.procs"
+BBHOSTSVCCOMMAS="HOST,DOMAIN,ORG.procs"
+BBNUMERIC="300111222333444757744"
+RECOVERED="0"
+DOWNSECS="0"
+DOWNSECSMSG=""
diff --git a/xymon/tar.client.logfiles.sh b/xymon/tar.client.logfiles.sh
new file mode 100755
index 0000000..40ababc
--- /dev/null
+++ b/xymon/tar.client.logfiles.sh
@@ -0,0 +1,65 @@
+#!/bin/sh
+
+# Purpose :
+# Create an XZ archive of all files between 2 dates.
+# Then remove these files
+
+# Call this script from an /var/lib/xymon/hostdata subdirectory or
+# /var/lib/xymon/histlogs subdirectory.
+
+# Vars {{{
+## Enable (0) or disable (1) debug
+debug=0
+
+## Colors {{{
+c_redb='\033[1;31m'
+c_magentab='\033[1;35m'
+c_reset='\033[0m'
+## }}}
+
+## Manage files of year
+date_year="2019"
+
+## Compress files between these dates
+date_start="${date_year}-01-01 00:00:01"
+date_end="${date_year}-12-31 23:59:59"
+
+## Best XZ compression level
+xz_compression_lvl="-9"
+## Fatest XZ compression level
+#xz_compression_lvl="-0"
+
+## Get current directory name
+current_dir=${PWD##*/}
+
+## Count the number of files
+match_files=$(find . -type f -newermt "${date_start}" -not -newermt "${date_end}" -not -iname "*.tar*" | wc -l)
+
+## Archive name
+tar_file_name="${date_year}.${current_dir}${xz_compression_lvl}.tar.xz"
+
+# }}}
+
+# If archive already exists
+if [ -s "${tar_file_name}" ]; then
+	printf "${c_redb}%-6b${c_reset}\n" "ERROR : ${tar_file_name} already exists (also ${match_files} files match the expected pattern). Please manage this directory manually or remove the archive or files then restart."
+	exit 1
+fi
+
+# If some files match
+if [ ! ${match_files} -eq "0" ]; then
+	[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : Create an archive for ${current_dir} files between ${date_start} and ${date_end} (${match_files} files) using XZ's compression level : ${xz_compression_lvl}."
+
+	## Get the list of files between the 2 dates and ignore tar files
+	find . -type f -newermt "${date_start}" -not -newermt "${date_end}" -not -iname "*.tar*" -print0 | tar cJf "${tar_file_name}" --null -T -
+
+	## Check previous return code and if the archive exists with size > 0
+	if [ "${?}" -eq "0" ] && [ -s "${tar_file_name}" ]; then
+		[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : ${tar_file_name} successfully created, the files can be deleted."
+		find . -type f -newermt "${date_start}" -not -newermt "${date_end}" -not -iname "*.tar*" -delete
+	fi
+else
+	[ "${debug}" -eq "0" ] && printf "${c_magentab}%-6b${c_reset}\n" "DEBUG : Skip ${current_dir}, no files found between ${date_start} and ${date_end}."
+fi
+
+exit 0
diff --git a/xymon/xymon.alert.sh b/xymon/xymon.alert.sh
new file mode 100755
index 0000000..7014ca4
--- /dev/null
+++ b/xymon/xymon.alert.sh
@@ -0,0 +1,59 @@
+#!/bin/sh
+# Purpose {{{
+## If Xymon server says that a probe is in error on a remote host, try to call the appropriate script.
+## For debugging messages, you can check xymon's logs (/var/log/xymon/alert.log)
+
+## How-to use : {{{
+### Define an alert in Xymon configuration file (/etc/xymon/alerts.cfg)
+#HOST=HOST.DOMAIN.ORG
+#  SCRIPT /PATH/TO/SCRIPT/xymon.alert.sh 1234567890 FORMAT=SCRIPT DURATION<20
+
+## }}}
+# }}}
+# Vars {{{
+DEBUG=1
+
+script_path="$(dirname -- ${0})"
+script_apt="${script_path}/xymon.apt.alert.sh"
+script_files="${script_path}/xymon.files.alert.sh"
+script_libs="${script_path}/xymon.libs.alert.sh"
+script_procs="${script_path}/xymon.procs.alert.sh"
+# }}}
+
+[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} is in error."
+
+# Match probe name with the script {{{
+case "${BBSVCNAME}" in
+	'apt' )
+	script_to_run="${script_apt}"
+	;;
+	'files' )
+	script_to_run="${script_files}"
+	;;
+	'libs' )
+	script_to_run="${script_libs}"
+	;;
+	'procs' )
+	script_to_run="${script_procs}"
+	;;
+	# default
+	* )
+	script_to_run="NOT.MANAGED"
+	;;
+esac
+# }}}
+
+# Call the next script if managed {{{
+if [ "${script_to_run}" != "NOT.MANAGED" ]; then
+	# Export vars {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — Export vars for ${script_to_run}"
+	export BBALPHAMSG
+	export BBHOSTNAME
+	export BBSVCNAME
+	# }}}
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — Run ${script_to_run} script."
+	"${script_to_run}"
+fi
+# }}}
+
+exit 0
diff --git a/xymon/xymon.apt.alert.sh b/xymon/xymon.apt.alert.sh
new file mode 100755
index 0000000..cface36
--- /dev/null
+++ b/xymon/xymon.apt.alert.sh
@@ -0,0 +1,62 @@
+#!/bin/sh
+# Purpose {{{
+## If Xymon server says that the last apt update is too old, try to run a new one.
+## 1. Create a ssh keyring for xymon user {{{
+# sudo mkdir -p -- /var/lib/xymon/.ssh/
+# sudo ssh-keygen -f /var/lib/xymon/.ssh/id_rsa -N '' -q
+# sudo chown -R xymon:xymon /var/lib/xymon/.ssh/
+## }}}
+## 2. Remote user {{{
+# Ensure to have the ${REMOTE_SSH_USER} available on remote hosts and allowed to connect with SSH.
+# Restrict the SSH access to a single SSH key from the Xymon server IP (~${REMOTE_SSH_USER}/.ssh/authorized_keys) :
+## from="IP.SRV.XYM.ON" ssh-rsa AAAAA…
+# Allow sudo commands to restart services and run apt update (/etc/sudoers.d/xymon-ssh) :
+## xymon-ssh ALL=(root:root) NOPASSWD: /usr/bin/apt update
+## xymon-ssh ALL=(root:root) NOPASSWD: /bin/systemctl restart *
+## }}}
+
+# }}}
+# Vars {{{
+DEBUG=1
+
+LOCAL_SSH_USER="xymon"
+REMOTE_SSH_USER="xymon-ssh"
+
+temp_dir=$(mktemp -d -t xymon-apt-alert-XXXXXX.tmp)
+debug_stdout="${temp_dir}/debug.stdout"
+debug_stderr="${temp_dir}/debug.stderr"
+# }}}
+
+# Create log files
+touch "${debug_stdout}" "${debug_stderr}"
+
+# Manage only apt probe {{{
+if [ "${BBSVCNAME}" = "apt" ]; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} error" >> "${debug_stdout}"
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} probe is not managed." >> "${debug_stderr}"
+	[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+	exit 0
+fi
+# }}}
+
+# Check if repos need to be updated {{{
+if echo "${BBALPHAMSG}" | grep -qE "\\&(red|yellow) Last apt update.*ago$" ; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test APT repos — APT repos need to be updated." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test APT repos — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo apt update" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo apt update" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# Also restart xymon-client service {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test APT repos — xymon-client also need to be restarted." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test APT repos — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart xymon-client.service" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart xymon-client.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# }}}
+fi
+# }}}
+
+# Remove empty error file
+[ -s "${debug_stderr}" ] || rm -f "${debug_stderr}"
+
+# Remove temp_dir if DEBUG is disable
+[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+
+exit 0
diff --git a/xymon/xymon.files.alert.sh b/xymon/xymon.files.alert.sh
new file mode 100755
index 0000000..28ff4bb
--- /dev/null
+++ b/xymon/xymon.files.alert.sh
@@ -0,0 +1,102 @@
+#!/bin/sh
+# Purpose {{{
+## If Xymon server says that a file is in error on a remote host, try to restart the related service.
+## 1. Create a ssh keyring for xymon user {{{
+# sudo mkdir -p -- /var/lib/xymon/.ssh/
+# sudo ssh-keygen -f /var/lib/xymon/.ssh/id_rsa -N '' -q
+# sudo chown -R xymon:xymon /var/lib/xymon/.ssh/
+## }}}
+## 2. Remote user {{{
+# Ensure to have the ${REMOTE_SSH_USER} available on remote hosts and allowed to connect with SSH.
+# Restrict the SSH access to a single SSH key from the Xymon server IP (~${REMOTE_SSH_USER}/.ssh/authorized_keys) :
+## from="IP.SRV.XYM.ON" ssh-rsa AAAAA…
+# Allow sudo commands to restart services (/etc/sudoers.d/xymon-ssh) :
+## xymon-ssh ALL=(root:root) NOPASSWD: /bin/systemctl restart *
+## }}}
+
+# }}}
+# Vars {{{
+DEBUG=1
+
+LOCAL_SSH_USER="xymon"
+REMOTE_SSH_USER="xymon-ssh"
+
+temp_dir=$(mktemp -d -t xymon-files-alert-XXXXXX.tmp)
+debug_stdout="${temp_dir}/debug.stdout"
+debug_stderr="${temp_dir}/debug.stderr"
+file_list="${temp_dir}/services.error.list"
+# }}}
+
+# Create log files
+touch "${debug_stdout}" "${debug_stderr}"
+
+# Manage only files probe {{{
+if [ "${BBSVCNAME}" = "files" ]; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} error" >> "${debug_stdout}"
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} probe is not managed." >> "${debug_stderr}"
+	[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+	exit 0
+fi
+# }}}
+
+# Check if a file exceeds it's modification time {{{
+if echo "${BBALPHAMSG}" | grep -qE "File was modified.*ago - should be.*" ; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test file — Some files exceeds their modification time." >> "${debug_stdout}"
+	# First restart Rsyslog service {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — First restart rsyslog service." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart rsyslog.service" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart rsyslog.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# }}}
+	## Get the list of files path
+	## TODO : Set a pattern for both yellow and red colors
+	echo "${BBALPHAMSG}" | sed -n 's;^\&yellow <a.*>\(.*\)</a>;\1;p' > "${file_list}"
+
+	while IFS= read -r file_path; do
+		[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while file_path loop — ${file_path} exceeds it's modification time." >> "${debug_stdout}"
+		# Match files path and services name {{{
+		case "${file_path}" in
+			# Cron
+			'/var/log/cron.log' )
+				service_name="cron"
+				;;
+			# default
+			* )
+				service_name="NOT.MANAGED"
+				;;
+		esac
+		# }}}
+
+		# Restart service if needed {{{
+		if [ "${service_name}" != "NOT.MANAGED" ] && [ "${service_name}" != "${previous_service_name}" ]; then
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while file_path loop — ${service_name} need to be restarted." >> "${debug_stdout}"
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while file_path loop — ssh -n -o StrictHostKeyChecking=no ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart ${service_name}.service" >> "${debug_stdout}"
+			ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart ${service_name}.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+			previous_service_name="${service_name}"
+		else
+			if [ "${service_name}" = "NOT.MANAGED" ]; then
+				[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while file_path loop — service for ${file_path} is not managed." >> "${debug_stdout}"
+			else
+				[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while file_path loop — ${service_name} was already restarted." >> "${debug_stdout}"
+			fi
+		fi
+		# }}}
+	done < "${file_list}"
+
+	# Also restart xymon-client service {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — xymon-client also need to be restarted." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart xymon-client.service" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart xymon-client.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# }}}
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test file — All files seems up to date." >> "${debug_stdout}"
+fi
+# }}}
+
+# Remove empty error file
+[ -s "${debug_stderr}" ] || rm -f "${debug_stderr}"
+
+# Remove temp_dir if DEBUG is disable
+[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+
+exit 0
diff --git a/xymon/xymon.libs.alert.sh b/xymon/xymon.libs.alert.sh
new file mode 100755
index 0000000..3bee8c7
--- /dev/null
+++ b/xymon/xymon.libs.alert.sh
@@ -0,0 +1,159 @@
+#!/bin/sh
+# Purpose {{{
+## If Xymon server says that a service is in error on a remote host, try to restart this service.
+## 1. Create a ssh keyring for xymon user {{{
+# sudo mkdir -p -- /var/lib/xymon/.ssh/
+# sudo ssh-keygen -f /var/lib/xymon/.ssh/id_rsa -N '' -q
+# sudo chown -R xymon:xymon /var/lib/xymon/.ssh/
+## }}}
+## 2. Remote user {{{
+# Ensure to have the ${REMOTE_SSH_USER} available on remote hosts and allowed to connect with SSH.
+# Restrict the SSH access to a single SSH key from the Xymon server IP (~${REMOTE_SSH_USER}/.ssh/authorized_keys) :
+## from="IP.SRV.XYM.ON" ssh-rsa AAAAA…
+# Allow sudo commands to restart services (/etc/sudoers.d/xymon-ssh) :
+## xymon-ssh ALL=(root:root) NOPASSWD: /bin/systemctl restart *
+## }}}
+
+# }}}
+# Vars {{{
+DEBUG=1
+
+LOCAL_SSH_USER="xymon"
+REMOTE_SSH_USER="xymon-ssh"
+
+temp_dir=$(mktemp -d -t xymon-libs-alert-XXXXXX.tmp)
+debug_stdout="${temp_dir}/debug.stdout"
+debug_stderr="${temp_dir}/debug.stderr"
+service_list="${temp_dir}/services.error.list"
+# }}}
+
+# Create log files
+touch "${debug_stdout}" "${debug_stderr}"
+
+# Manage only libs probe {{{
+if [ "${BBSVCNAME}" = "libs" ]; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} error" >> "${debug_stdout}"
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} probe is not managed." >> "${debug_stderr}"
+	[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+	exit 0
+fi
+# }}}
+
+# Check if host need to reboot {{{
+if echo "${BBALPHAMSG}" | grep -qE "\\&yellow Machine should be reboot.*" ; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test kernel — The host need to be rebooted." >> "${debug_stdout}"
+fi
+# }}}
+
+# Check if a service need to restart
+if echo "${BBALPHAMSG}" | grep -qE "\\&yellow The following processes.*" ; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — Some services need to be restarted." >> "${debug_stdout}"
+	# Get the list of binaries path
+	echo "${BBALPHAMSG}" | sed -n 's/^  \(\/.*\) (.*)/\1/p' > "${service_list}"
+
+	while IFS= read -r bin_path; do
+		[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while bin_path loop — ${bin_path} use old libs." >> "${debug_stdout}"
+		# Match binaries path and services name {{{
+		case "${bin_path}" in
+			# Apache2
+			'/usr/sbin/apache2' )
+				service_name="apache2"
+				;;
+			# Arpwatch
+			'/usr/sbin/arpwatch' )
+				service_name="arpwatch"
+				;;
+			# Dbus
+			'/usr/bin/dbus-daemon' )
+				service_name="dbus"
+				;;
+			# lvmetad − LVM metadata cache daemon
+			'/sbin/lvmetad' )
+				service_name="lvm2-lvmetad"
+				;;
+			# Netdata
+			'/usr/sbin/netdata' )
+				service_name="netdata"
+				;;
+			# blkmapd − pNFS block layout mapping daemon
+			'/usr/sbin/blkmapd' )
+				service_name="nfs-utils"
+				;;
+			# Mumble-server
+			'/usr/sbin/murmurd' )
+				service_name="mumble-server"
+				;;
+			# Nginx
+			'/usr/sbin/nginx' )
+				service_name="nginx"
+				;;
+			# Ntp
+			'/usr/sbin/ntpd' )
+				service_name="ntp"
+				;;
+			# Nslcd
+			'/usr/sbin/nslcd' )
+				service_name="nslcd"
+				;;
+			# PHP-FPM 7.0
+			'/usr/sbin/php-fpm7.0' )
+				service_name="php7.0-fpm"
+				;;
+			# PHP-FPM 7.3
+			'/usr/sbin/php-fpm7.3' )
+				service_name="php7.3-fpm"
+				;;
+			# Postfix
+			'/usr/lib/postfix/sbin/pickup' | '/usr/lib/postfix/qmgr' | '/usr/lib/postfix/sbin/tlsmgr' | '/usr/lib/postfix/sbin/qmgr' )
+				service_name="postfix"
+				;;
+			# Rdnssd
+			'/sbin/rdnssd' )
+				service_name="rdnssd"
+				;;
+			# Systemd-journald
+			'/lib/systemd/systemd-journald' )
+				service_name="systemd-journald"
+				;;
+			# Systemd-logind
+			'/lib/systemd/systemd-logind' )
+				service_name="systemd-logind"
+				;;
+			# default
+			* )
+				service_name="NOT.MANAGED"
+				;;
+		esac
+		# }}}
+
+		# Restart service if needed {{{
+		if [ "${service_name}" != "NOT.MANAGED" ] && [ "${service_name}" != "${previous_service_name}" ]; then
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while bin_path loop — ${service_name} need to be restarted." >> "${debug_stdout}"
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while bin_path loop — ssh -n -o StrictHostKeyChecking=no ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart ${service_name}.service" >> "${debug_stdout}"
+			ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart ${service_name}.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+			previous_service_name="${service_name}"
+		else
+			if [ "${service_name}" = "NOT.MANAGED" ]; then
+				[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while bin_path loop — service for ${bin_path} is not managed." >> "${debug_stdout}"
+			else
+				[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while bin_path loop — ${service_name} was already restarted." >> "${debug_stdout}"
+			fi
+		fi
+		# }}}
+	done < "${service_list}"
+
+	# Also restart xymon-client service {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — xymon-client also need to be restarted." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : Test service — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart xymon-client.service" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart xymon-client.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# }}}
+fi
+
+# Remove empty error file
+[ -s "${debug_stderr}" ] || rm -f "${debug_stderr}"
+
+# Remove temp_dir if DEBUG is disable
+[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+
+exit 0
diff --git a/xymon/xymon.procs.alert.sh b/xymon/xymon.procs.alert.sh
new file mode 100755
index 0000000..9729190
--- /dev/null
+++ b/xymon/xymon.procs.alert.sh
@@ -0,0 +1,107 @@
+#!/bin/sh
+# Purpose {{{
+## If Xymon server says that a service is in error on a remote host, try to
+## restart this service.
+## 1. Create a ssh keyring for xymon user {{{
+# sudo mkdir -p -- /var/lib/xymon/.ssh/
+# sudo ssh-keygen -f /var/lib/xymon/.ssh/id_rsa -N '' -q
+# sudo chown -R xymon:xymon /var/lib/xymon/.ssh/
+## }}}
+## 2. Remote user {{{
+# Ensure to have the ${REMOTE_SSH_USER} available on remote hosts and allowed
+# to connect with SSH.
+# Restrict the SSH access to a single SSH key from the Xymon server IP
+# (~${REMOTE_SSH_USER}/.ssh/authorized_keys) :
+## from="IP.SRV.XYM.ON" ssh-rsa AAAAA…
+# Allow sudo commands to restart services (/etc/sudoers.d/xymon-ssh) :
+## xymon-ssh ALL=(root:root) NOPASSWD: /bin/systemctl restart *
+## }}}
+## 3. Xymon Configuration {{{
+#    PROC monitoring need to display the real service name in it's description :
+## PROC %^/sbin/rpcbind MIN=1 MAX=1 COLOR=red "TEXT=rpcbind"
+# You can add more information about this proc if you an underscore "_" :
+##   PROC %^/usr/sbin/rpc.idmapd MIN=1 MAX=1 COLOR=red "TEXT=NFS-server_rpc.idmapd"
+## This way, the script will only take the text before the underscore "_" as the
+## service name to be restarted.
+# Don't add whitespaces in the description of a process.
+
+## }}}
+# }}}
+
+# Vars {{{
+DEBUG=1
+
+REMOTE_SSH_USER="xymon-ssh"
+
+temp_dir=$(mktemp -d -t xymon-procs-alert-XXXXXX.tmp)
+debug_stdout="${temp_dir}/debug.stdout"
+debug_stderr="${temp_dir}/debug.stderr"
+service_list="${temp_dir}/services.error.list"
+# }}}
+
+# Create log files
+touch "${debug_stdout}" "${debug_stderr}"
+
+# Manage only procs probe {{{
+if [ "${BBSVCNAME}" = "procs" ]; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} error" >> "${debug_stdout}"
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : ${BBHOSTNAME} — ${BBSVCNAME} probe is not managed." >> "${debug_stderr}"
+	[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+	exit 0
+fi
+# }}}
+
+# Get the list of processes with an error
+echo "${BBALPHAMSG}" | grep -E "&(red|yellow)" | cut -d" " -f2- | tr '[:upper:]' '[:lower:]' > "${service_list}"
+
+# If any error on a process
+if [ -s "${service_list}" ]; then
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : process list — Some processes seems to be in error." >> "${debug_stdout}"
+	while IFS= read -r line; do
+		## Pattern "req. between" {{{
+		if echo "${line}" | grep -q -E -- ".* \\(found .*, req. between .* and .*\\)" ; then
+		[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — Pattern \"req. between\"." >> "${debug_stdout}"
+			service_name="$(echo "${line}" | cut -d" " -f1 | sed 's/_.*//')"
+			process_found="$(echo "${line}" | cut -d" " -f3 | tr  -d ',')"
+			process_min="$(echo "${line}" | cut -d" " -f6)"
+			process_max="$(echo "${line}" | cut -d" " -f8 | tr  -d ')')"
+		fi
+		## }}}
+		## Pattern "req. .* or more" {{{
+		if echo "${line}" | grep -q -E -- ".* \\(found .*, req. .* or more\\)" ; then
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — Pattern \"req. .* or more\"." >> "${debug_stdout}"
+			service_name="$(echo "${line}" | cut -d" " -f1 | sed 's/_.*//')"
+			process_found="$(echo "${line}" | cut -d" " -f3 | tr  -d ',')"
+			process_min="$(echo "${line}" | cut -d" " -f5)"
+			process_max="nolimit"
+		fi
+		## }}}
+		[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — Found ${process_found} process(es) for ${service_name} service and require between ${process_min} and ${process_max}." >> "${debug_stdout}"
+		# Restart service if needed {{{
+		if [ "${process_found}" ] && [ "${process_min}" ] && [ "${process_found}" -lt "${process_min}" ]; then
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — ${service_name} need to be restarted." >> "${debug_stdout}"
+			[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart ${service_name}.service" >> "${debug_stdout}"
+			ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart ${service_name}.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+		else
+				[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : while process loop — ${service_name} service is not managed." >> "${debug_stdout}"
+		fi
+		# }}}
+	done < "${service_list}"
+
+	# Also restart xymon-client service {{{
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : process list — xymon-client also need to be restarted." >> "${debug_stdout}"
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : process list — ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null ${REMOTE_SSH_USER}@${BBHOSTNAME} sudo systemctl restart xymon-client.service" >> "${debug_stdout}"
+	ssh -n -o StrictHostKeyChecking=no -o UserKnownHostsFile=/dev/null "${REMOTE_SSH_USER}"@"${BBHOSTNAME}" "sudo systemctl restart xymon-client.service" >> "${debug_stdout}" 2>> "${debug_stderr}"
+	# }}}
+else
+	[ "${DEBUG}" -eq "0" ] && printf '\e[1;35m%-6s\e[m\n' "DEBUG : process list — No error on any process." >> "${debug_stdout}"
+fi
+
+# Remove empty error file
+[ -s "${debug_stderr}" ] || rm -f "${debug_stderr}"
+
+# Remove temp_dir if DEBUG is disable
+[ "${DEBUG}" -eq "0" ] || rm -rf -- "${temp_dir}"
+
+exit 0